Accredited Abrasive Wheels certificate

Abrasive Wheels Training

Fabricators, fitters and maintenance teams.

Training is delivered on your site across Aberdeen, Aberdeenshire and North-East Scotland; contact us to discuss dates and a quote.

Tell us how many operators need training and what machines you use.

Call 07867 933 018Get a quote

Learning built around bench, angle and cut-off grinders

This course is for fabricators, fitters and maintenance teams. The practical work centres on bench, angle and cut-off grinders, with the assessment matched to the machine, task and operating conditions the candidate will face.

Skills covered

  • Wheel selection, mounting and balancing
  • Guards, PPE and dust/noise control
  • Daily checks and defect reporting

Practical situations covered

The exercises reflect the tasks and constraints attached to abrasive wheels work.

  1. Exercise 1

    Cutting stainless on a fabrication bench with localised LEV

  2. Exercise 2

    Field cutting threaded bar with a 9-inch angle grinder near other trades

  3. Exercise 3

    Bench-grinder dressing and tool-rest gap (max 1.6 mm) routine

Errors the course addresses

These course-specific errors are dealt with through instruction, observation and practical assessment.

  • Wrong wheel on the wrong machine — RPM mismatch is the #1 burst-wheel cause
  • Guards removed 'for the awkward cut' and never refitted
  • No ring-test or storage discipline — moisture-damaged wheels then run at full speed

Published safety context

5,500+

UK angle-grinder injuries treated in A&E each year, many eye and hand.

Source: RoSPA / NHS injury surveillance.

Abrasive wheels regulations: what the law actually asks for

The old Abrasive Wheels Regulations 1970 were replaced long ago. Today the abrasive wheel regulations people search for sit inside PUWER 1998, which requires every employer to make sure anyone using work equipment has adequate training, and HSE guidance HSG17, which sets out good practice for selecting, storing, mounting and using wheels and discs.

In practice that means anyone who mounts or changes a wheel on a bench, angle or cut-off grinder should be trained and competent to do so, and employers should keep a record of who that is. Abrasive wheels training gives your team that record, along with the habits that stop wheels bursting: matching the wheel speed to the machine, checking for damage, keeping the guard on and setting the tool rest.

Abrasive wheels training in North-East Scotland and in warehouses

Most teams we train are fabricators, fitters and maintenance staff, but grinders turn up in many places: warehouse maintenance benches, workshop units, yards cutting threaded bar and site teams with a cut-off saw. The course runs half to a full day and leads to an accredited abrasive wheels certificate, so warehouse operatives and site staff come away with certification an auditor can see.

Training runs on your own site, using the grinders and discs your team actually uses. That is quicker to organise for a group in Aberdeen, Aberdeenshire and North-East Scotland, and it means the practical part of the day is about your machines, your guards and your storage, not a classroom example. Tell us how many people need training and what equipment they use.

Abrasive Wheels Training questions

How long is abrasive wheels training valid for?
The regulations set no fixed expiry date. Training stays valid while the person remains competent, but employers commonly arrange refresher training at regular intervals, after an incident, or when new equipment is introduced.
Does abrasive wheel training expire?
The certificate does not lapse in law, but competence fades. Most employers set their own refresher interval and record it in their training matrix.
Can you do abrasive wheel training online?
Theory can be learned online, but mounting a wheel safely is a practical skill. Our course is delivered on your site so each person mounts and checks wheels under supervision.
Do I need abrasive wheel training?
Yes, if you mount, change or use abrasive wheels at work. PUWER 1998 requires adequate training, and HSG17 recommends that only trained people mount wheels.
What does abrasive wheels training cover?
Wheel selection, mounting and balancing; Guards, PPE and dust/noise control; Daily checks and defect reporting.
Which equipment is used?
Bench, angle and cut-off grinders. Training and assessment use the relevant equipment available on your site.
Who is the course for?
Fabricators, fitters and maintenance teams. Prerequisites: Aged 16+. Tool familiarity helpful but not required.
What certification is issued?
Accredited Abrasive Wheels certificate. The course covers PUWER 1998 and HSG17.
How long does training take?
Half to full day.